Hallite bearing seal 533G
Technical details
| OPERATING CONDITIONS | METRIC | INCH |
| Maximum Speed | 5.0 m/sec | 15.0 ft/sec |
| TemperatureRange | -40°C + 120°C | -40°F + 250°F |
| Surface roughness | µmRa | µmRt | µinCLA | µinRMS |
| Dynamic Sealing Face – Rod Ød1 | 0.4 | 4 max | 16 | 18 |
| Static Sealing Face – Rod ØD2L1 | 3.2 max | 16 max | 125 max | 140 max |
| Dynamic Sealing Face – Piston Ød1 | 0.4 | 4 max | 16 | 18 |
| Static Sealing Face – Piston Ød2L1 | 3.2 max | 16 max | 125 max | 140 max |
| Housing Details & Tolerances | |||
| L1 in | +0.015 +0.010 | ||
| r1 in | 0.016 max | ||
| Rod Ød1 in | f9 | ||
| ØD2 in | Ød1 + 2S | +0.004 -0.000 | |
| ØD3 in | Ød1 + G | ||
| Piston ØD1 in | H11 | ||
| Ød2 in | ØD1 -2S | +0.000 -0.004 | |
| Ød3 in | ØD1 – G | ||
| 1/8 nominal cross sections – in | S = 0.126 | G max 0.080 | G min 0.031 |
| 3/32 nominal cross sections – in | S = 0.093 | G max 0.060 | G min 0.031 |
| 1/16 nominal cross sections – in | S = 0.062 | G max 0.040 | G min 0.031 |
| INCH | ||||
| Part no. | ØD1 | Ød2 | L1 | S |
| F10047 | 2.5 | 2.25 | 0.5 | 0.125 |
| F30046 | 2.5 | 2.25 | 0.5 | 0.125 |
| F30073 | 3.25 | 3 | 0.75 | 0.125 |
| F30355 | 3.312 | 3.126 | 0.75 | 0.093 |
| F30084 | 3.5 | 3.25 | 0.5 | 0.125 |
| F30340 | 3.5 | 3.25 | 0.75 | 0.125 |
| F30226 | 3.5 | 3.314 | 0.5 | 0.093 |
| F30111 | 4.25 | 4 | 0.75 | 0.125 |
| F30116 | 4.5 | 4.25 | 0.5 | 0.125 |
| F10128 | 4.5 | 4.25 | 0.5 | 0.125 |
| F30227 | 4.5 | 4.25 | 0.75 | 0.125 |
| F30359 | 4.6 | 4.35 | 0.5 | 0.125 |
| F30134 | 5.25 | 5 | 0.75 | 0.125 |
| F30137 | 5.5 | 5.25 | 0.5 | 0.125 |
| F30228 | 5.5 | 5.25 | 0.75 | 0.125 |
| F10166 | 6 | 5.75 | 0.625 | 0.125 |
| F30148 | 6 | 5.75 | 0.625 | 0.125 |
| F30345 | 6 | 5.75 | 0.75 | 0.125 |
| F30152 | 6.25 | 6 | 0.75 | 0.125 |
| F30155 | 6.5 | 6.25 | 0.5 | 0.125 |
| F30361 | 6.5 | 6.25 | 0.5 | 0.125 |
| F30229 | 6.5 | 6.25 | 0.75 | 0.125 |
| F30161 | 7.25 | 7 | 0.75 | 0.125 |
| F30163 | 7.5 | 7.25 | 0.5 | 0.125 |
| F30341 | 7.5 | 7.25 | 0.75 | 0.125 |
| F30357 | 8.413 | 8.163 | 0.75 | 0.125 |
| F30417 | 8.5 | 8.25 | 0.5 | 0.125 |
| F30342 | 8.5 | 8.25 | 0.75 | 0.125 |
| F30415 | 8.61 | 8.36 | 0.5 | 0.125 |
| F30362 | 9.878 | 9.628 | 0.75 | 0.125 |