AY Wiper Seal
Descriptions
The purpose of the profile AY Ultrathan® double lip wiper is to prevent dust, dirt,
grains of sand, and metal swarfs. This is achieved by a special design which largely
prevents scoring, protects the guiding parts and extends the service life of the seals.
In addition, the sealing lip facing the media reduces the residual oil film. The profile AY
double wiper ring closes the rod in the direction of the cylinder. No special screwrings
or brackets are required for installation. No close tolerances and no metal inserts are
required. The wiper is supplied as a continuous ring and can easily be pressed into
the groove.
The polyurethane compound ensures excellent properties with regard to dry run, increased wear resistance, and extended service life due to good resistance to ozone
and radiation caused by weather conditions.
We recommend profile AY Ultrathan® double-lip wiper when using PTFE rod seals or
whenever the residual oil film is to be kept at a minimum.
Features
• Extreme wear resistance.
• Excellent media resistance in case of
suitable compound selection.
• Suitable compounds available for
special requirements of the chemical
process industry.
• Suitable compounds available for special requirements of the food processing
industry.
• Dimensions according to DIN ISO 6195,
Type C.
• Installation in closed and undercut
housings.
• Additional sizes of machined products
available on short notice.
Range of application
Double wiper rings profile AY are designed for axially operated rods in hydraulic and
pneumatic cylinders, lifters, and rod guidances.
Operating temperature | -35 °C to +100 °C |
Pneumatics | -35 °C to +80 °C |
Sliding speed | ≤ 2 m/s |
Compounds
Ultrathan® P5008 is a polyurethane-based Parker compound with a hardness of approx. 93 Shore A. In comparison with other polyurethane materials currently available
on the market it excels because of its increased heat resistance, improved against
hydrolysis, and lower compression set values.
Installation
The profile AY double lip wiper ring can easily be snapped into grooves of simple
design. Any contact of the wiper lip with piston rod eyes or other connecting parts
should be avoided.
However, we recommend the wiper lip to be out-side the housing, so that the wipedoff dirt falls off.
d | D | H | h | D2 | L |
8 | 13 | 4.1 | 3.1 | 10.5 | 3.5 |
10 | 16 | 4.8 | 3.6 | 12.5 | 4 |
12 | 18 | 4.8 | 3.6 | 14.5 | 4 |
14 | 20 | 4.8 | 3.6 | 16.5 | 4 |
15 | 21 | 4.8 | 3.6 | 17.5 | 4 |
16 | 22 | 4.8 | 3.6 | 18.5 | 4 |
18 | 24 | 4.8 | 3.6 | 20.5 | 4 |
20 | 26 | 4.8 | 3.6 | 22.5 | 4 |
22 | 28 | 4.8 | 3.6 | 24.5 | 4 |
25 | 31 | 4.8 | 3.6 | 27.5 | 4 |
28 | 36 | 5.8 | 4.5 | 31 | 5 |
30 | 38 | 5.8 | 4.5 | 33 | 5 |
32 | 40 | 5.8 | 4.5 | 35 | 5 |
35 | 43 | 5.8 | 4.5 | 38 | 5 |
36 | 44 | 5.8 | 4.5 | 39 | 5 |
37 | 45 | 5.8 | 4.5 | 40 | 5 |
40 | 48 | 5.8 | 4.5 | 43 | 5 |
45 | 53 | 5.8 | 4.5 | 48 | 5 |
50 | 58 | 5.8 | 4.5 | 53 | 5 |
51 | 59 | 5.8 | 4.5 | 54 | 5 |
55 | 65 | 6.8 | 5.3 | 58 | 6 |
56 | 66 | 6.8 | 5.3 | 59 | 6 |
60 | 70 | 6.8 | 5.3 | 63 | 6 |
63 | 73 | 6.8 | 5.3 | 66 | 6 |
65 | 75 | 6.8 | 5.3 | 68 | 6 |
70 | 80 | 6.8 | 5.3 | 73 | 6 |
75 | 85 | 6.8 | 5.3 | 78 | 6 |
80 | 90 | 6.8 | 5.3 | 83 | 6 |
85 | 95 | 6.8 | 5.3 | 88 | 6 |
90 | 100 | 6.8 | 5.3 | 93 | 6 |
100 | 110 | 6.8 | 5.3 | 103 | 6 |
110 | 125 | 9.5 | 7.5 | 114 | 8.5 |
120 | 135 | 9.5 | 7.5 | 124 | 8.5 |
125 | 140 | 9.5 | 7.5 | 129 | 8.5 |
138 | 158 | 9.5 | 7.5 | 142 | 8.5 |
140 | 155 | 9.5 | 7.5 | 144 | 8.5 |
160 | 175 | 9.5 | 7.5 | 164 | 8.5 |