BS Rod Seal
Descriptions
The profile BS Ultrathan® rod seal is a lip seal with a secondary sealing lip and tight
fit at the outer diameter. Wear and dry run are largely prevented by the additional lubricant retained under the seal, created by the secondary lip. In some cases this second sealing lip may even act as a substitute for a costly tandem-arrangement when
complete sealing under certain working conditions can only be achieved by two seals
placed one behind the other in separate housings.
For telescopic cylinders, we recommend the version with a 4-mm profile width.
Features
• Excellent sealing performance due to
elongated contact area and multiple
sealing lips.
• Exceptionally high static and dynamic
sealing performance.
• Enhanced sealing performance in nonpressurized conditions.
• Penetration of air into the system is
largely prevented.
• Robust seal profile for harshest operating conditions.
• Extreme wear resistance.
• Easier installation.
• Insensitive to pressure peaks.
• Improved lubrication due to pressure
medium deposit in the dynamic contact
area.
• High extrusion resistance.
• Excellent media resistance in case of
suitable compound selection.
• Suitable compounds available for
special requirements of the chemical
process industry.
• Suitable compounds available for special requirements of the food processing
industry.
• Dimensions according to ISO 5597.
• Short radial assembly depth.
• Installation in closed and undercut
housings.
• Additional sizes of machined products
available on short notice.
Range of application
Mainly for the sealing of piston rods and plungers in heavy duty applications in mobile and stationary hydraulics. The dimensions mainly conform to the requirements of
ISO 5597 and ISO 3320 for housing and diameters respectively.
Operating pressure | ≤ 400 bar |
Operating temperature | -35 °C to +110 °C |
Sliding speed | ≤ 0.5 m/s |
Media | Hydraulic oils based on mineral oil |
Compounds
The compound Ultrathan® P5008 is a Parker material based on polyurethane with a
hardness of approx. 93 Shore A. Its main advantages in comparison with other polyurethane materials currently available on the market are the increased heat resistance
and the lower compression set.
For media containing water, we recommend our hydrolysis-resistent polyurethane
compound P5001.
Installation
The seals should have an axial clearance (see columns H and L). To avoid damage at
the sealing lips, the seals should not be pulled over sharp edges during installation.
Normally these seals may be snapped into closed grooves. Where access is restricted
special assembly tools may be required. Proposals for the design of such tools will be
provided on request. For gap sizes see chapter “Maximum Gap Allowance”.
d | D | H | L |
8 | 16 | 5.7 | 6.3 |
9 | 16 | 5.7 | 6.3 |
10 | 16 | 4.5 | 5.3 |
10 | 17 | 5.7 | 6.3 |
10 | 18 | 5.7 | 6.3 |
12.7 | 19.05 | 4.5 | 5.3 |
14 | 20 | 5.7 | 6.3 |
14 | 22 | 5.7 | 6.3 |
14 | 24 | 7.3 | 8 |
16 | 24 | 5.8 | 6.3 |
16 | 26 | 7.3 | 8 |
18 | 28 | 7.3 | 8 |
20 | 30 | 7.3 | 8 |
22 | 32 | 7.3 | 8 |
25 | 33 | 6.5 | 7.3 |
25 | 35 | 7.3 | 8 |
26 | 36 | 10 | 11 |
28 | 36 | 7 | 7.5 |
28 | 38 | 7.3 | 8 |
30 | 40 | 10 | 11 |
30 | 45 | 10 | 11 |
32 | 42 | 7.3 | 8 |
32 | 42 | 10 | 11 |
32 | 45 | 10 | 11 |
35 | 45 | 10 | 11 |
35 | 50 | 10 | 11 |
36 | 46 | 7.3 | 8 |
36 | 48 | 10 | 11 |
36 | 51 | 10 | 11 |
37 | 47 | 10 | 11 |
40 | 48 | 11.5 | 12.5 |
40 | 49.52 | 9.6 | 10.5 |
40 | 50 | 10 | 11 |
40 | 52 | 7.4 | 8 |
40 | 52 | 8 | 9 |
40 | 55 | 11.4 | 12.5 |
43 | 53 | 7.3 | 8 |
45 | 53 | 5.6 | 6.3 |
45 | 55 | 7.3 | 8 |
45 | 55 | 10 | 11 |
45 | 57.7 | 9.6 | 10.5 |
45 | 60 | 10.5 | 11.5 |
45 | 60 | 11.4 | 12.5 |
46 | 56 | 10 | 11 |
48 | 56 | 11.5 | 12.5 |
50 | 60 | 7.3 | 8 |
50 | 60 | 10 | 11 |
50 | 62.7 | 9.6 | 10.5 |
50 | 65 | 10 | 11 |
50 | 65 | 11.4 | 12.5 |
50.8 | 63.5 | 9.5 | 10.3 |
52 | 62 | 10 | 11 |
55 | 65 | 10 | 11 |
55 | 65 | 11 | 12 |
55 | 67 | 10 | 11 |
56 | 71 | 11.4 | 12.5 |
58 | 66 | 11.5 | 12.5 |
60 | 68 | 13 | 14 |
60 | 70 | 7.5 | 8.5 |
60 | 70 | 10 | 11 |
60 | 75 | 10 | 11 |
63 | 71 | 8 | 9 |
63 | 78 | 10 | 11 |
63 | 78 | 11.4 | 12.5 |
65 | 73 | 11.5 | 12.5 |
65 | 75 | 12 | 13 |
65 | 85 | 11.4 | 12.5 |
68 | 78 | 12 | 13 |
70 | 80 | 12 | 13 |
70 | 85 | 10 | 11 |
70 | 85 | 11.4 | 12.5 |
74 | 82 | 11.5 | 12.5 |
75 | 85 | 11.5 | 12.5 |
75 | 88 | 10 | 11 |
75 | 90 | 10 | 11 |
77 | 87 | 11.5 | 12.5 |
78 | 86 | 11.5 | 12.5 |
80 | 88 | 11.5 | 12.5 |
80 | 90 | 12 | 13 |
80 | 95 | 11.4 | 12.5 |
80 | 100 | 12 | 13 |
81 | 89 | 11.5 | 12.5 |
82.55 | 95.25 | 9.53 | 10.3 |
85 | 93 | 11.5 | 12.5 |
85 | 100 | 12 | 13 |
90 | 98 | 11.5 | 12.5 |
90 | 105 | 11.4 | 12.5 |
92 | 107 | 11.4 | 12.5 |
95 | 115 | 12 | 13 |
97 | 105 | 13 | 14 |
100 | 108 | 12 | 13 |
100 | 120 | 12 | 13 |
100 | 120 | 14.5 | 16 |
105 | 113 | 11.5 | 12.5 |
105 | 117 | 9.1 | 10 |
107 | 115 | 11.5 | 12.5 |
110 | 125 | 14.5 | 16 |
110 | 130 | 14.5 | 16 |
118 | 126 | 13 | 14 |
120 | 128 | 11.5 | 12.5 |
120 | 130 | 14 | 15 |
125 | 133 | 11.5 | 12.5 |
128 | 136 | 9.1 | 10 |
128 | 140 | 9.1 | 10 |
130 | 145 | 12 | 13 |
140 | 160 | 14.5 | 16 |
143 | 151 | 13 | 14 |
145 | 153 | 11.5 | 12.5 |
150 | 170 | 15 | 16 |
152 | 160 | 9.1 | 10 |
152 | 164 | 9.1 | 10 |
160 | 185 | 18.2 | 20 |
167 | 175 | 11.5 | 12.5 |
167 | 176 | 11.5 | 12.5 |
170 | 200 | 18 | 19 |
171 | 179 | 13 | 14 |
176 | 186 | 12 | 13 |
177.7 | 195 | 9.73 | 11.3 |
180 | 188 | 9.1 | 10 |
180 | 188 | 11.5 | 12.5 |
180 | 192 | 9.1 | 10 |
193 | 201 | 11.5 | 12.5 |
200 | 211 | 12 | 13 |
200 | 225 | 18.2 | 20 |
209.55 | 226.77 | 9.73 | 11.3 |
212 | 220 | 9.1 | 10 |
212 | 224 | 9.1 | 10 |
220 | 228 | 11.5 | 12.5 |
220 | 250 | 22.7 | 25 |
223 | 231 | 11.5 | 12.5 |
228.5 | 246 | 9 | 10 |
230 | 260 | 22.7 | 25 |
250 | 280 | 22.7 | 25 |
266.7 | 284 | 9.73 | 11.3 |
280 | 310 | 18 | 19 |