Pneumatic Seal E4
The profile E4 piston seal is a lip seal specially developed for use in pneumatics. The dimensions of the profile E4 standard series correspond to the cylinder diameters according to ISO 3320, CETOP RP 52 P, RP 43 P and RP 53 P. Profile E4 is fully interchangeable with the profile C2 standard series formerly used in pneumatics.
• Due to application-optimized geometry and compounds suitable for use in oiled as well as in oil-free air (after initial lubrication on assembly).
• Suitable for cylinders with dead-center cushioning.
• Long service life thanks to applicationoptimized compounds.
• Smooth running due to optimum lubricant-retaining sealing lip geometry.
• Easier installation.
• Suitable for fully automatic installation.
• Assembly on one-part piston is possible.
• Excellent media resistance in case of suitable compound selection.
• Installation in closed housings.
NBR:
• Special seal geometry ensures optimal function even in case of flow-controlled exhaust air.
• High temperature resistance in case of suitable compound selection.
• Good wear resistance.
PUR:
• Low compression set.
• Pressure relief grooves at the back of the seal ensure optimal function even in case of flow-controlled exhaust air.
• Robust seal profile for harshest operating conditions.
• Extreme wear resistance.
Range of application | |
Operating pressure | ≤ 16 bar |
Operating temperature | -30 °C to +80 °C |
Sliding speed | ≤ 1 m/s |
Media | Compressed air, both lubricated and oil free (after greasing for fitting) |
Installation
The profile E4 lip seals are simply pulled over the piston into the groove. To avoid damaging the seal lips during installation, sharp edges should be removed from the piston and the cylinder tube.Under oil-free conditions it is important to obtain a solid lubrication film inside the cylinder tube. This must be achieved before assembly to ensure a long service life of the seal.For piston guidance we recommend the profile F2 piston guidance tape. Please refer to our profile F2 for details of the piston outside diameter and the gap measurements.
D, | d, | H, | L, | d1, |
10 | 5 | 3 | 3.5 | 9 |
12 | 6 | 4 | 4.5 | 11 |
12 | 7 | 4 | 4.5 | 11 |
14 | 8 | 4 | 4.5 | 13 |
16 | 8 | 5.5 | 6 | 15 |
16 | 9 | 5 | 5.5 | 15 |
16 | 10 | 4 | 4.5 | 15 |
20 | 12 | 5.5 | 6 | 19 |
20 | 14 | 4 | 4.5 | 19 |
20.5 | 14 | 4 | 4.5 | 19.5 |
22 | 16 | 5 | 5.5 | 21 |
24 | 16 | 5.5 | 6 | 23 |
25 | 15.5 | 5.8 | 6.3 | 24 |
25 | 17 | 4.5 | 5 | 24 |
25 | 17 | 5.5 | 6 | 24 |
28 | 18 | 7 | 7.5 | 26.5 |
32 | 20 | 6.5 | 7 | 30 |
32 | 22 | 7 | 7.5 | 30.5 |
32 | 24 | 5.5 | 6 | 31 |
34 | 24 | 7 | 7.5 | 32.5 |
36 | 26 | 7 | 7.5 | 34.5 |
40 | 30 | 7 | 7.5 | 38.5 |
42 | 30 | 6 | 6.5 | 40 |
45 | 33 | 9 | 10 | 43 |
45 | 37 | 7 | 7.5 | 44 |
50 | 40 | 7 | 7.5 | 48.5 |
60 | 50 | 7 | 7.5 | 58.5 |
63 | 53 | 7 | 7.5 | 61.5 |
65 | 55 | 7 | 7.5 | 63.5 |
70 | 58 | 7 | 7.5 | 68 |
75 | 65 | 7.5 | 8 | 73.5 |
80 | 68 | 8.5 | 9.5 | 78 |
84 | 72 | 8.5 | 9.5 | 82 |
100 | 88 | 8.5 | 9.5 | 98 |
105 | 93 | 8.5 | 9.5 | 103 |
110 | 98 | 8.5 | 9.5 | 108 |
120 | 105 | 10 | 11 | 117.5 |
125 | 110 | 10 | 11 | 122.5 |
130 | 115 | 10 | 11 | 127.5 |
140 | 125 | 10 | 11 | 137.5 |
150 | 135 | 10 | 11 | 147.5 |
160 | 140 | 14 | 15 | 155 |
160 | 145 | 10 | 11 | 157.5 |
180 | 160 | 14 | 15 | 175 |
200 | 180 | 14 | 15 | 195 |
220 | 199 | 15 | 16 | 215 |
250 | 225 | 18 | 19 | 242.5 |
250 | 226 | 16 | 17 | 242.5 |
250 | 230 | 14 | 15 | 245 |
320 | 295 | 14 | 15 | 312.5 |
320 | 295 | 17 | 18 | 312.5 |
470 | 440 | 21 | 22 | 460 |